Performix Coatings
Performix Coatings
3920 Pheasant Ridge Drive Blaine, MN 55449
Phone: 1-800-969-5432 ext 6104
Fax: 763.785.2058
E-Mail: contact@performixcoatings.com
Website: www.performixcoatings.com
Print Back
F-970 Softouch is a fast dry, high quality, high solids, water base, 100% polyurethane coating that produces a unique Softouch finish on molded and fabricated polyurethane foams commonly used for the latest trend in ultra contemporary furniture and exotic display pieces.

F-970 Softouch can also be applied to EVA, PVC, EPS, x-link PE or minicell foams.

Other applications include life size costumes, movie props, Cosplay etc. F-970 Softouch is also high solids, very low V.O.C. material, which makes it an Emission Control Coating System, eccs®.

Finally, a one component product you can rely on batch after batch. The durability, safety, ease of use, water clean up, as well as cosmetic appearance, you expect. The service and quality you deserve.
Unit of Measure

Technical Specs

Brands

 N/A Performix®

Approximate Solids Weight

 N/A 60 %

Temperature Use Range

 N/A 0 to 225 ºF

Block Resistance at 140 Degree Fahrenheit (ºF) Temperature

 N/A 4 h

Shelf Life

 N/A 1+ years at 77 ºF unopened container

Coverage

 N/A 45 ft²/gal at 35 mils 60 ft²/gal at 27.5 mils 80 ft²/gal at 20 mils

Tensile

 N/A 1,347 psi

Tensile Test Method

 N/A American Society for Testing and Materials (ASTM D-412)

Elongation

 N/A 478 %

Elongation Test Method

 N/A American Society for Testing and Materials (ASTM D-412)

Tear Resistance

 N/A 0.13

Tear Resistance Test Method

 N/A American Society for Testing and Materials (ASTM D-1004)

Freeze Thaw Stability

 N/A Good

Finish

 N/A Satin

Ultraviolet (UV) Stability

 N/A Good

Alternative Products

 N/A PDC® 3119 (2 component system)

Other Features Include

Other Features Include

 N/A Non-flammable, very safe and easy to use
Pass methenamine pill burn test
Water clean-up

Surface Preparations

N/A All surfaces to be coated must be free of any oils, dust, mold release or loose foam particles. Use of a quality lint roller on all surfaces just prior to coating is recommended.

USE ADEQUATE VENTILATION. GENTLY MIX BEFORE EACH USE

Coating Process Top Coat / Base Coat (Spray)

N/A Use of F-977, F830 or F-874 Muraculon Base Coat at 12 mils minimum is required before applying F-970 Top Coat. Make sure Base Coat is fully dry before applying Top Coat. F-970 Top Coat will not hide surface defects of Base Coat. If necessary sand smooth or repair defects of Base Coat, see hints below.

N/A

  1. Apply 1st application using wet, overlapping spray coats, holding gun 10"-12" from surface, using a 4"-6" pattern. Allow to dry 45-60 minutes or until dry to the touch.
  2. Apply 2nd application using wet, overlapping spray coats, holding gun 10"-12" from surface, using a 4"-6" pattern. Allow to dry 45-60 minutes or until dry to the touch.
  3. For best results wet sand [see wet sanding instructions] before spray applying 3rd coat or any additional coats repeating this process each time.

N/A Binks® model 2100 gun or equivalent
Nozzle: 66SS
Cap: 66SS
Needle: 565
Material: 20 psi
Atomization: 10-25 psi
Dilution: not recommended
Clean up: immediately with water - if allowed to dry, use Acetone or M.E.K.

Airless or air assisted airless equipment may be used. Dilution is not suggested. Gently mix before spraying. Apply wet, overlapping coats, holding gun 12"-24" from surface, using 6"-12" pattern.
Tip size: 0.011-0.026
Pressure: as needed
Dilution: Not Recommended
Clean up: immediately with water - if allowed to dry, use Acetone or M.E.K.

Coating Process for Closed Cell Foams

N/A Molded PU, PVC, EVA, X-Link or Mini Cell Foams

N/A

  1. Apply 1st application using wet, overlapping spray coats, holding gun 10"-12" from surface, using a 4"-6" pattern. Allow to dry 45-60 minutes or until dry to the touch.
  2. Apply 2nd application using wet, overlapping spray coats, holding gun 10"-12" from surface, using a 4"-6" pattern. Allow to dry 45-60 minutes or until dry to the touch.
  3. For best results wet sand [see wet sanding instructions] before spray applying 3rd coat or any additional coats repeating this process each time.

N/A

  1. Using a high quality 1/4" nap roller, apply F-970 Softouch to foam surface making sure to apply liberally and only in one direction. Move roller very slowly [1" per second] across the surface using only light pressure. Allow to dry 45-60 minutes or until dry to the touch.
  2. Repeating step one apply second coat across [90 degrees] to the first coat to ensure a more uniform and even roller coat. Apply liberally, very slowly and in one direction only. Make sure to check for any runs or sags quickly after roller application. If found, use roller without adding any F-970 Softouch and re-apply to entire area slowly in an effort to redistribute excess F- 970 Softouch. Allow to dry 45-60 minutes or until dry to the touch.
  3. For best results wet sand [see wet sanding instructions] before applying 3rd coat or any additional coats repeating this process each time.
Wet Sanding - Wet sanding is best accomplished using a 3M Pro Grade Sanding Sponge. For best results start by using the COURSE grade and then MEDIUM grade sponge. Start by placing surface to be wet sanded vertically to prevent prolonged contact with puddled water. Apply water to sponge and using a circular motion remove high spots or imperfections [sags/ runs] as needed. Make sure to rinse sponge frequently. DO NOT wet sand any area more than 60 seconds at one time. After sanding rinse away any debris and dab dry with lint free cloth. Allow to dry before repeating in same area.

Water sensitivity - F-970 Softouch is water based and like all water based coatings and paints can be sensitive to prolonged contact with water. If dried F-970 Softouch does come in contact with water, dab dry using a lint free cloth. It is normal for the color to change [lighter] after prolonged contact. After drying the color will return to its original shade. If products being coated require greater moisture resistance its recommended you contact Technical Service for our high performance cross linked finish.

Hints

N/A A dry film thickness of 18-20 minimum is recommended for best results. Best results are achieved when liquid temperature of F-970 Softouch is between 70-75ºF and air temperature is 70-75ºF. Allow at least overnight dry before stacking or storing coated items. Always use proper ventilation and protection.

Note

N/A For Industrial Use Only.

We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the applications of this information or the safety and suitability of our products, either alone or in combination with other product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products whether used alone or in combination with other products. Ever changing V.O.C. regulations in your area may require you to contact local authorities for proper use and/or disposal of this product. Should you need further assistance, please contact PLASTI DIP INTERNATIONAL technical service.

PDC and eccs are registered trademarks of PLASTI DIP INTERNATIONAL
Performix and logo are trademarks of PLASTI DIP INTERNATIONAL
BINKS is a registered trademark of BINKS MFG. CO., Franklin Park, IL
3M is a registered trademark of 3M St. Paul, MN