Skip To Content
ISO 9001:2015
mail_outline contact@performixcoatings.com call 1-800-969-5432 ext 6104 search

Catalog

Request Information
F-892 is a vinyl based clear top coat which is used over F-818 or F-861 as well as Muraculon coatings as a satin finish. While remaining soft and flexible, F-892 will also improve tensile strength, abrasion, block and stain resistance.
Unit of Measure

Technical Specs

Brands

 N/A Performix®

Solids Weight

 N/A 3.5 %

Coverage

 N/A 175 ft²/gal at 1 mil

Shelf Life

 N/A 1+ years at 77 ºF unopened container

Temperature Use Range

 N/A -30 to 200 ºF

Block Resistance at 140 Degree Fahrenheit (ºF) Temperature

 N/A 4 h

Finish

 N/A Satin

Chemical Resistance

 N/A Mineral Oil: Very Good
Saline: Very Good
Urea (6% In H2O): Very Good
Betadine (iodine): Very Good (Stained After 5 Minutes.)
Gasoline: Good
Machine Oil: Very Good
Blood: Very Good
All Purpose Cleaner: Very Good
Acid (10% Sulfuric in H2O): Very Good
Alcohol: Very Good

In House Test Results [ASTM D-1308]

Alternative Products

 N/A For satin top coat see F-760

Surface Preparations

N/A MIX WELL BEFORE USE.
All surfaces to be coated must be free of any oils, dust or loose foam particles.

USE ADEQUATE VENTILATION.

Spraying

N/A GENTLY MIX BEFORE SPRAYING.
Pressure pot/conventional sprayers may be used. Apply wet, overlapping coats, holding gun 6"-12" from surface, using 4"-6" pattern. Allow 10-20 minutes minimum dry time before applying additional coats or turning part over. To speed drying of F-892, allow to air dry 5 minutes, then place in mild heat, 95°F-120°F, with mild air movement, until completely dry. Make sure heat source is safe for this use and that you ventilate properly. Recommended dry film thickness is 1 mil.

Recommended Equipment and Settings

N/A Binks® model 2100 gun
Nozzle: 63B
Cap: 63PB
Needle: 363A
Material: 20 psi
Atomization: 10-25 psi
Dilution: As needed
Clean up: Methyl Ethyl Ketone, M.I.B.K., Toluene or Xylene.

Industrial/commercial airless equipment may be used. Use as described above.

Tip size: 0.011-0.019

Pressure: As needed

Dilution: Not recommended

Hints

N/A Recommended thinners, M.I.B.K or Xylene. Always use proper ventilation and protection. When using a dip tank, always leave at least 6" from fluid surface to tank top to minimize skinning over. Allow overnight drying whenever possible. Avoid excessive air movement, heat or humidity.

Note

N/A For Industrial Use Only.

We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the applications of this information or the safety and suitability of our products, either alone or in combination with other product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products whether used alone or in combination with other products. Ever changing V.O.C. regulations in your area may require you to contact local authorities for proper use and/or disposal of this product. Should you need further assistance, please contact PLASTI DIP INTERNATIONAL technical service.

PDC is a registered trademark of PLASTI DIP INTERNATIONAL
Performix and logo are trademarks of PLASTI DIP INTERNATIONAL
BINKS is a registered trademark of BINKS MFG. CO., Franklin Park, IL