Skip To Content
ISO 9001:2015
mail_outline contact@performixcoatings.com call 1-800-969-5432 ext 6104 search

Catalog

Request Information
PLASTI DIP® F-866 is high build air dry, synthetic rubber coating that can be easily applied by spraying, brushing or dipping. PLASTI DIP® F-866 resists moisture, acids, abrasion, weathering, electrical shock, skidding/slipping, corrosion; coats and gives a comfortable, controlled, color coded grip to all types of tools; lawn and garden, mechanical, electrical, woodworking and masonry.

PLASTI DIP® F-866 can also be applied to:
Wood: Seals and protects from weathering and prevents splinters.
Metal: Reduces vibration, deadens sound, prevents corrosion, insulates electrically and from extreme temperatures.
Glass: Shatterproofs glass objects (available in clear).
Rope/Fabrics: Weatherproofs, prevents rotting and fraying.
Plastics: Protects delicate surfaces from scratches.
Rubber: Weatherproofs, wear resistant.
Unit of Measure

Technical Specs

Solids Weight

 N/A 28 %

Tensile

 N/A 3,740 psi

Tensile Test Method

 N/A American Society for Testing and Materials (ASTM D-638)

Elongation

 N/A 430 %

Elongation Test Method

 N/A American Society for Testing and Materials (ASTM D-638)

Cut Resistance

 N/A Very Good

Cut Resistance Test Method

 N/A American Society for Testing and Materials (ASTM D-1044)

Coverage

 N/A 40 ft²/gal at 10 mils

Stone Abrasion

 N/A Excellent

Stone Abrasion Test Method

 N/A American Society for Testing and Materials (ASTM D-3170)

Shelf Life

 N/A 1+ years at 77 ºF unopened container

Viscosity Range at 77 Degree Fahrenheit (ºF) Temperature (±2 Degree Fahrenheit (ºF)

 N/A 80 to 100 K.U.

Shore A Hardness

 N/A 70 duro

Salt Spray

 N/A Passed 1,000 hours

Salt Spray Test Method

 N/A American Society for Testing and Materials (ASTM B-117)

Temperature Use Range

 N/A -30 to 200 ºF

Permeability

 N/A 0.03 grains/ft²/h

Permeability Test Method

 N/A American Society for Testing and Materials (ASTM E-96)

Dielectric

 N/A 1400 V/mil

Dielectric Test Method

 N/A American Society for Testing and Materials (ASTM D-149)

Chemical Resistance

 N/A Acids, Alkalis, Pollutants: Excellent
Petroleums: Limited

Alternative Products

 N/A F-698 F-819 HCFeccs® F-688/F-688's' PLASTI DIP® F-829

Surface Preparations

N/A MIX WELL BEFORE USE.
All surfaces to be coated must be free of all oils, grease, dirt, wax and loose rust. A sandblasted or rough surface improves adhesion. Use PLASTI DIP® PRIMER F-716 or H.P. PRIMER F-938 on all metals for best results.

Spraying

N/A Pressure pot may be used (siphon cup not recommended). Dilute with recommended thinners up to 50% as needed. Gently mix before spraying. Apply wet overlapping coats, holding gun 6"-12" from surface, using a 4"-6" pattern. Allow 10-20 minutes dry time before applying additional coats to desired thickness.

Recommended Equipment and Settings

N/A Binks® model 2100 gun
Nozzle: 63B
Needle: 663A
Material: 20-25 psi
Atomization: 15-25 psi
Dilution: As needed
Cap: 63PB (up to 50% dilution) or 66SD (up to 50% dilution) for heavier build up.
Clean up: See recommended thinners.

SPRAYING: Airless equipment may be used. Use as described above.
Tip size: 0.011-0.019
Pressure: As needed
Dilution: Up to 50%

Dipping

N/A Dilute with recommended thinners up to 25% as needed. Gently mix before each use. Do not introduce air bubbles. Insert item 1" every 5 seconds. Remove at same rate. Allow 30-40 minutes (dry to the touch) dry time before applying additional coats to desired thickness.

Brushing

N/A Dilute with recommended thinners up to 25% as needed. Gently mix before each use. Apply wet overlapping coats using a soft natural bristle brush. Allow 10-20 minutes (dry to the touch) dry time before applying additional coats to desired thickness.

Hints

N/A Recommended thinners: Toluene or VM&P Naphtha. A dry film thickness of 12-15 mils is recommended for best results. Approximate dry mil thickness per coat, dipping 6-8 mils; brushing 4-5 mils; spraying 2-5 mils. Allow 4 hours dry time per coat before use. Allow overnight drying whenever possible. When using a dip tank, allow 6" minimum from fluid surface to tank top to avoid "skinning over". Avoid excessive air movement, heat or humidity. Always use proper ventilation and protection.

Note

N/A For Industrial Use Only.

We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the applications of this information or the safety and suitability of our products, either alone or in combination with other product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products whether used alone or in combination with other products. Ever changing V.O.C. regulations in your area may require you to contact local authorities for proper use and/or disposal of this product. Should you need further assistance, please contact PLASTI DIP INTERNATIONAL technical service.

Plasti Dip, HCF, Performix and logo are registered trademarks of PLASTI DIP INTERNATIONAL
BINKS is a registered trademark of BINKS MFG. CO., Franklin Park, IL