Skip To Content
ISO 9001:2015
mail_outline contact@performixcoatings.com call 1-800-969-5432 ext 6104 search

Catalog

Request Information
HCF eccs®/AIM Compliant Coating/RTS meets requirements for AIM Industrial Maintenance Coating of 450 g/l or less VOC.
HCF eccs®/AIM Compliant Coating/RTS is an air dry, all in one primer/top coat, flexible acrylic water base coating that can be easily applied by brushing or dipping. HCF eccs®/AIM Compliant Coating/RTS resists corrosive, caustic and acidic agents, most chemicals, chemical fumes, abrasion, impact and extreme weather conditions. Excellent for use on hand rails, brackets, HVAC equipment, pipes, pipe hangers etc.

HCF eccs®/AIM Compliant Coating/RTS bonds to metal, wood, concrete and plastics without primers. HCF eccs®/AIM Complaint Coating/RTS has the safety of water base with the performance of solvent base coatings. It's very low V.O.C.'s, non-flammable and high solids content make it an Emission Control Coating System, eccs®, that can be air dried or heat cured to meet production demands. Use HCF eccs®/AIM Complaint Coating for dipping or brushing applications.
Unit of Measure

Technical Specs

Brands

 N/A Performix®

Solids Weight

 N/A 36 %

Finish

 N/A Semi-Gloss

Tensile

 N/A 230 psi

Tensile Test Method

 N/A American Society for Testing and Materials (ASTM D-2370)

Temperature Use Range

 N/A 0 to 250 ºF

Coverage

 N/A 100 ft²/gal at 5 mils

Shelf Life

 N/A 1+ years at 77 ºF unopened container

Elongation

 N/A 230 %

Elongation Test Method

 N/A American Society for Testing and Materials (ASTM D-2370-82)

Abrasion

 N/A 0.0005 inches/100 cycles

Abrasion Test Method

 N/A American Society for Testing and Materials (ASTM D-4060)

Permeability

 N/A Limited

Weatherability

 N/A Excellent 7 to 10 Years

Weatherability Test Method

 N/A American Society for Testing and Materials (ASTM G-53)

Dielectric

 N/A 1100 V/mil

Dielectric Test Method

 N/A American Society for Testing and Materials (ASTM D-149)

Chemical Resistance

 N/A Petroleum: Excellent
Acid, Alkaline: Good
Alcohol, Ketone, Chlorinated Solvent: Limited
Water Soak: Limited

Alternative Products

 N/A HCF eccs®/AIM Complaint Coating

Surface Preparations

N/A MIX WELL BEFORE USE.
All surfaces to be coated must be free of all oils, grease, dirt, wax, and loose rust. A sandblasted or rough surface improves adhesion.

USE ADEQUATE VENTILATION.

Spraying

N/A Pressure pot/conventional sprayers may be used. Gently mix before spraying. Apply wet, overlapping coats, holding gun 6"-12" from surface, using a 4"- 6" pattern. Allow to completely dry before applying additional coats to desired thickness.

Recommended Equipment and Settings

N/A Gun: Binks® model 2100
Nozzle: 63B
Cap: 63PB or 66SD-3 for heavier build up
Needle: 663 A
Material: 25 psi
Atomization: 15-25 psi
Dilution: None required
Clean up: Water

Industrial/commercial airless equipment may be used. Use as described above.

Tip sizes: 0.011-0.019
Pressure: As needed
Dilution: None needed

Hints

N/A For storage or dip tank containers, use poly or galvanized steel. A dry film thickness of 6-8 mils is recommended for best results. Allow overnight drying whenever possible. To speed drying, mild heat (95°F-110°F) and air flow may be used. Do not stack or store parts in contact with each other if not fully cured. Avoid excessive air movement, heat or humidity. Always use proper ventilation and protection.

Note

N/A For Industrial Use Only.

We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the applications of this information or the safety and suitability of our products, either alone or in combination with other product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products whether used alone or in combination with other products. Ever changing V.O.C. regulations in your area may require you to contact local authorities for proper use and/or disposal of this product. Should you need further assistance, please contact PLASTI DIP INTERNATIONAL technical service.

PLASTI DIP,eccs, Performix and logo are registered trademarks of PLASTI DIP INTERNATIONAL
BINKS is a registered trademark of BINKS MFG. CO., Franklin Park, IL