Skip To Content
ISO 9001:2015
mail_outline contact@performixcoatings.com call 1-800-969-5432 ext 6104 search

Catalog

Request Information
PLASTI DIP®/ AIM Compliant Coating meets requirements for AIM Industrial Maintenance Coating of 450 g/l or less VOC.

PLASTI DIP® /AIM Compliant Coating is an air dry, synthetic rubber coating that can be easily applied by spraying, brushing or dipping. PLASTI DIP®/ AIM Compliant Coating resists high humidity, immersion in water, waste water, corrosive, caustic and acidic agents, most chemicals, chemical fumes, abrasion, impact and extreme weather conditions. Excellent for use on hand rails, brackets, HVAC equipment, pipes, pipe hangers etc.
Unit of Measure

Technical Specs

Brands

 N/A Performix®

Solids Weight

 N/A 24 %

Tensile

 N/A 3,740 psi

Tensile Test Method

 N/A American Society for Testing and Materials (ASTM D-638)

Elongation

 N/A 430 %

Elongation Test Method

 N/A American Society for Testing and Materials (ASTM D-638)

Cut Resistance

 N/A Very Good

Cut Resistance Test Method

 N/A American Society for Testing and Materials (ASTM D-1044)

Coverage

 N/A 40 ft²/gal at 10 mils

Stone Abrasion

 N/A Excellent

Stone Abrasion Test Method

 N/A American Society for Testing and Materials (ASTM D-3170)

Shelf Life

 N/A 1+ years at 77 ºF unopened container

Viscosity Range at 77 Degree Fahrenheit (ºF) Temperature (±2 Degree Fahrenheit (ºF)

 N/A 80 to 100 K.U.

Weatherability

 N/A 7 to 10 years

Weatherability Test Method

 N/A American Society for Testing and Materials (ASTM G-53)

Shore A Hardness

 N/A 70 duro

Shore A Hardness Test Method

 N/A American Society for Testing and Materials (ASTM D-2240)

Salt Spray

 N/A Passed 1,000 hours

Salt Spray Test Method

 N/A American Society for Testing and Materials (ASTM B-117)

Temperature Use Range

 N/A -30 to 200 ºF

Permeability

 N/A 0.03 grains/ft²/h

Permeability Test Method

 N/A American Society for Testing and Materials (ASTM E-96)

Dielectric

 N/A 1400 V/mil

Dielectric Test Method

 N/A American Society for Testing and Materials (ASTM D-149)

Alternative Products

 N/A PLASTI DIP® /AIM Compliant Coating/RTS, HCF eccs® AIM Compliant Coatings

Chemical Resistance

 N/A Corrosive, Acid, Alkaline: Excellent
Petroleum: Limited

Surface Preparations

N/A MIX WELL BEFORE USE.
All surfaces to be coated must be free of all oils, grease, dirt, wax and loose rust. A sandblasted or rough surface improves adhesion. Use PLASTI DIP® PRIMER/ AIM Compliant, on all metals for best results.

Spraying

N/A Please see TDS for PLASTI DIP® AIM Compliant Coating/ RTS

Dipping

N/A Gently mix before each use. Do not introduce air bubbles. Insert item 1" every 5 seconds. Remove at same rate. Allow 30-40 minutes (dry to the touch) dry time before applying additional coats to desired thickness. A minimum of 3-4 dip coats are recommended for most applications.

Brushing

N/A Gently mix before each use. Apply wet overlapping coats using a soft natural bristle brush. Allow 10-20 minutes (dry to the touch) dry time before applying additional coats to desired thickness. A minimum of 5-6 brush coats are recommended for most applications.

Hints

N/A Clean Up: Aromatic 100 or Methyl Acetate exempt solvents only. A dry film thickness of 12-15 mils is recommended for best results. Approximate dry mil thickness per coat, dipping 6-8 mils; brushing 2-3 mils. Allow 4 hours dry time per coat before use. Allow overnight drying whenever possible. When using a dip tank, allow 6" minimum from fluid surface to tank top to avoid "skinning over". Avoid excessive air movement, heat or humidity. Always use proper ventilation and protection.

Note

N/A For Industrial Use Only.

We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the applications of this information or the safety and suitability of our products, either alone or in combination with other product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products whether used alone or in combination with other products. Ever changing V.O.C. regulations in your area may require you to contact local authorities for proper use and/or disposal of this product. Should you need further assistance, please contact PLAST DIP INTERNATIONAL technical service

Plasti Dip, HCF, Performix and logo are registered trademarks of PLASTI DIP INTERNATIONAL
BINKS is a registered trademark of BINKS MFG. CO., Franklin Park, IL