Skip To Content
ISO 9001:2015
mail_outline contact@performixcoatings.com call 1-800-969-5432 ext 6104 search

Catalog

Request Information
F-663's' is an acrylic water base coating designed to protect polystyrene and expanded polystyrene foams from impact damage as well as improve appearance. F-663's' has excellent chemical, abrasion and impact resistance. With its semi-gloss finish, F-663's' is perfect for logos, letters or any 3 dimensional item used for display purposes. This high performance acrylic is also excellent for outdoor use on polystyrene dock foams, packaging items, decoys and the list goes on. It's very low VOC's; non-flammable and high solids content make it an Emission Control Coating System, eccs®. Use F-663's' anywhere common paints fail on polystyrene foams and enjoy the long term benefits of a quality, easy to use water base coating.
This product contains Dibutyl Phthalate which is restricted for use in certain children’s toys and childcare articles (reference; CPSIA 2008).
Unit of Measure

Technical Specs

Brands

 N/A Performix®

Solids Weight

 N/A 36 %

Tensile

 N/A 1,800 psi

Tensile Test Method

 N/A American Society for Testing and Materials (ASTM D-2370)

Temperature Use Range

 N/A 35 to 180 ºF

Elongation

 N/A 230 %

Elongation Test Method

 N/A American Society for Testing and Materials (ASTM D-2370)

Block Resistance at 120 Degree Fahrenheit (ºF) Temperature

 N/A 4 h

Shelf Life

 N/A 1+ years at 77 ºF unopened container

Coverage

 N/A 110 ft²/gal at 5 mils

Finish

 N/A Gloss

Chemical Resistance

 N/A Acids, Alkaline, Aliphatic: Good Alcohols, Ketones, Chlorinated Solvents: Limited Aromatic, Glycols: Fair In House Test Results Petroleum's: Excellent

Chemical Resistance Test Method

 N/A American Society for Testing and Materials (ASTM D-1308)

Note for Chemical Resistance

 N/A In House Test Results (ASTM D-1308)

Alternative Products

 N/A F-674

Other Features Include

N/A Wide selection of colors.
High solids, high coverage.
Safe, easy to use water base.

Surface Preparations

N/A MIX WELL BEFORE USE.

All surfaces to be coated must be free of any oils, dust or loose foam particles.

USE ADEQUATE VENTILATION.

Spraying

N/A Pressure pot/conventional spray equipment may be used. Gently mix before spraying. Apply wet, overlapping coats, holding gun 6-12" from surface, using a 4-6" pattern. Allow to completely dry before applying additional coats to desired thickness.

Recommended Equipment and Settings

N/A Binks® Model 2100 Gun
Nozzle: 66SS
Cap: 66SD
Needle: 565
Material: 20psi
Atomization: 15-30psi
Dilution: As needed (water)
Clean up: Water, mild solvent if allowed to dry

Brush/Roller

N/A Gently mix before each use. Apply wet overlapping coats using a foam brush, pad or roller. Allow to completely dry before applying additional coats to desired thickness.

Hints

N/A A dry film thickness of 6-8 mils is recommended for best results. Allow overnight drying whenever possible. To speed drying, mild heat (95°F-110°F) and air flow may be used. Most water base products take up to one week to fully cure, if not heat cured. Avoid excessive air movement, heat or humidity. Always use proper ventilation and protection.

Note

N/A For Industrial Use Only.

We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the applications of this information or the safety and suitability of our products, either alone or in combination with other product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products whether used alone or in combination with other products. Ever changing V.O.C. regulations in your area may require you to contact local authorities for proper use and/or disposal of this product. Should you need further assistance, please contact PLAST DIP INTERNATIONAL technical service.

PDC and eccs are registered trademarks of PLASTI DIP INTERNATIONAL
Performix and logo are trademarks of PLASTI DIP INTERNATIONAL
BINKS is a registered trademark of BINKS MFG. CO., Franklin Park, IL